Maximum Reports Samples For Students

The rationale of this report is to present results of the Emissions Inventory conducted for Northern Arizona University’s (NAU) criteria pollutant emissions. The report shall be in terms of both the emissions trends for the university and the resulting impacts these emissions have on the surrounding environment and human health. Emissions data collected by Northern Arizona University Industrial Hygienist, Jim Biddle, was used to create a comprehensive report of nine years of emissions data for NAU over a thirteen year time span (1999-2012). No data was available for the years 2000, 2002, 2004, or 2006.
The four criteria ...

1.0 AIM
3
1.1 SCOPE
3
2.0 METHOD
3
3.0 DEVISING THE MODEL
4
4.0 COMMENTS
6
5.0 CONCLUSION
6
6.0 References
7

Appendix 1, Figure 1: sketch of paddocks showing both fencing options
8

Appendix 2, Figure 2: rows of width, length and area from spread sheet
9
Appendix 3, Figure 3: graphs of area vs. width for fencing option 1 and 2
10

1.0 AIM
The objective is to use mathematical techniques to determine maximum area of land that can be fenced using a given size of fencing material. An equation will be obtained to describe the ...

Group Number:

TA’s Name:
ABSTRACT
This laboratory report examines a two-part experiment carried. The first experiment was carried out to test both the Kirchhoff’s loop and junction rule. The results of the experiment have been presented in the report. Using the results collected the loop and junction. The second part of the experiment involved determining the Kirchhoff’s loop and junction rule. The maximum power transfer equation has been derived in the report.

Objectives

The object of the experiment is to test both the Kirchhoff’s loop and junction rule. The experiment was also aimed at determining how maximum power ...

#222060 : Finite Element Analysis of a Clamp Frame

PART 1 INITIAL STRESS ANALYSIS

Analysis Model is prepared with the dimension as shown in Fig.1-1
Fig.1-1 Initial Specification

Material propertie as shown in Table1-1 is adopted in the model.

All the degree of freedom is fixed at the lower platform, as shown in Fig.1-2;
Fig.1-2 Boundary Condition at the Lower Platform

Upward axial force (15000N) is applied on the inner surface of the cylindrical hole, as shown in Fig.1-3;

Fig.1-3 Axial Force at the Cylindrical Hole

Mesh is created with a default size, as shown in Fig.1-4;

Fig.1-4 Mesh with a Default Size : 12481 Nodes / 7372 Elements

After the calculation, the following results are obtained;

1. A Stress Plot of the von Mises Stress for the entire frame, clearly showing the area of highest stress.
Fig.1-5 Von Mises Stress : Max. Stress = 204.382(Mpa)
2. A plot of the resultant ...

First A. Author, Second B. Author, Jr., and Third C. Author, Member, IEEE
Abstract—In this experiment, a hand dynamometer was used to measure the grip strength of a subject. The forearm muscles were engaged in an activity, and the grip recorded. The electromyogram (EMG) activity was related to the grip strength by making a graph of the maximum grip strength against area under the EMG activity’s absolute integral during the contraction of muscle. Data was recorded from the dominant and non-dominant forearms of the subject and the electrical activity of each forearm compared to its diameter. Prolonged ...

This report presents the static analysis of a beam that is going to be used for lifting equipment in a building. A commercial software package, SolidWorks, is used to perform a set of FEA simulations. Numerical results are compared with theoretical values of maximum stress and deflection for a cantilever beam.
1. Part A
The first part of this report describes a cantilever beam with one end fully constrained and a point force of 5 kN applied at the opposite end. Three cross sections are considered, namely, a wide flange section (I-shape), a T section and a channel cross ...

Cut Off Region of a Transistor

The transistor goes into the cutoff region when the base current (IB) is equal to zero. The collector leakage current ICEO under such conditions is quite low due to the effect of thermally-generated carriers. This means that ICEO can be neglected in the circuit analysis such that VCE will be equal to VCC. During the cutoff region, both the base-collector and the base emitter junctions are reverse biased. Subscript CEO means a representation of the collector to emitter with the base open. This is represented in the circuit below.

Saturation Region of a Transistor

Forward biasing of the base-emitter junction increases the base current. ...

Introduction

The object of the paper is to analyze the above relationship over a range of pressures extending above and below atmospheric pressure.
Data were obtained for the pressure and temperature of a saturated steam-water mixture in equilibrium over a wide range of pressures and temperatures. The “raw” experimental data are given at the end of this document and the apparatus used are described below.

The object of this exercise is to:

a) Use the raw data to produce a table of absolute pressure .v. absolute (thermodynamic) saturation temperature over the whole range of the data provided.
b) Compare this data to equivalent data taken from steam ...

- Introduction
The dc circuit theories of Norton and Thevenin are investigated in this practical. The Thevenin theorem states that any network of resistors and sources (voltage and current) when viewed from any two points in a network can be replaced by an equivalent circuit of a single resistance (Thevenin Resistance) in series with a voltage source (Thevenin voltage). Similarly, Norton’s theorem is aimed at replacing the network of resistors and sources with an equivalent circuit of a constant current source in parallel with a resistance.
- Results

Experimental data

The Thevenin resistance of the circuit is calculated by replacing ...

Abstract

The objective of this experiment is examination of diffraction and interference of visible light when it is passed across narrow double and single slits. In order to do so, the diffraction patterns of light will be investigated through collection of pertinent data relating to the distance between pattern’s centres and maxima. Of particular interest in this experiment is the varying intensity of light and respective positions on the display screen as ascertained trough measurement and calculation of width and separation distances for respective patterns. The experiment concludes by highlighting the wave attributes of visible light as manifested in ...

a Course, College, country
b Course, College, country

Abstract

Tensile strength is a kind of force which is applied by pulling something such as rope, wire etc. to the point where it breaks [1]. The tensile strength of the material is the maximum amount of tensile stress that it can take before failure [1]. There is different kind of tensile strength yield strength, ultimate strength, breaking strength. The tensile strength can be found using tensile test which is a kind of the mechanical test [2]. Tensile test are simple, inexpensive and fully standardized. The motto of this paper is to ...

Olomoze is choosing between Argentina and Hungary to expand its operations and fanchises. Among other things, demand estimation was done by relationship analysis based on certain assumptions. Olomoze’s products are food items purchased and consumed by individual persons. So the estimation is done on the basis of the population of the countries considered.
Quantitative market research information are not available at this point which could provide an estimate of how much of a country’s population consume the products. Assumptions were thus made to get some comparative figures between the two countries.

Argentina

The World Bank classifies Argentina as ...

Group

Abstract
Material selection is an important stage in engineering design. Engineers use various materials with different mechanical properties in building of structures. These mechanical properties include; tensile strength, yield strength, proof stress, Young's modulus, shears modulus of rigidity and ductility amongst others. Material selection increases the performance as well as durability of the engineering component. The expected life, cost, nature of loading and working environment are some of the factors that assist engineers to select materials for particular application. Therefore, engineers and designers must be able to determine the properties of these materials before they use them. Engineers use ...

Answer 1(a):

CREDIT CARD MARKET STRUCTURE
The functionality of a credit card revolves around a well managed system. It is a mode of payment based on a promise between the bank and the holder of the card that he / she will make the payment in the future.
In the highly competitive market of today the bank intends to maximize its customer share by promoting the use of credit cards more and more. They do this by minimizing the limits off the card to ensure maximum usage. The more customers purchase using credit cards the more beneficial it is for the ...

Abstract

The voltage drop across sections of a circuit and the current can be determined using Kirchoff’s laws. For currents and voltages, the algebraic sum at any node should be zero. Using this basic principle, any circuit can be analyzed for current and voltage. This paper will present and experiment performed to validate Kirchoff’s laws. According to Thevenin, a complex circuit can be simplified into an equivalent circuit to obtain voltage and current. By Superposition theorem, effect of sources in a circuit can be considered singly and then summed up. It was determined that the laws are true.

Objective

...

Executive Summary

Rocky Marketing Network is faced with two issues concerning to their workforce i.e. low retention rate and poor performance that are telling upon their profitability and challenging their position with a comparison to their competitors. The current report has been prepared after a careful investigation of the causes of the reported issues. After a deep study, it was detected that both the issues are overlapping each other to a considerable extent and are the products of poor HRM performance. Furthermore, it is suggested that the company can tackle both the issues by taking appropriate initiatives, which are as follows:
...

ABSTRACT

In the vibrating beam experiment, an aluminum cantilever beam was made to vibrate. An accelerometer transducer was used to convert the mechanical vibrations into a signal that was fed into an oscilloscope via a power supply. The oscilloscope mapped the signal into a sine curve and displayed it on the screen.
The oscillations’ decay curve was studied and the beam’s damping ratio was determined. The decay curve’s logarithmic decrement was used to determine the beam’s damping ratio and its natural frequency.
The beam’s damping ratio was observed to be underdamped at a damping ratio of ...

This jack is operated by turning the handle in a clockwise direction. The action of the screw then makes the load rise (Cleghorn, 2010). A research was carried out on the weights of most family cars to determine the maximum weight the jack can lift. The average weight of a family car according to the research is about 1660kg, much of this weight being on the engine side, about two thirds. The jack will support a load of up to 610kg. With a safety factor of 1.63, the maximum lift of the jack can be determined as follows:Maximum lift * ...

Abstract

Bridges are the most complicated structures to design in the Engineering field. The following experiment conducted using spaghetti and any type of glue in building a bridge model. The experiment involved testing how much weight can the spaghetti hold in tensile using a tensile strength testing machine. The experiment aimed at making a practical representation of real bridges and the forces on them. Three main real bridges are discussed, truss bridge, srch bridge, and suspension bridge. The tests were conducted through hanging weights on the constructed spagheti bridge and determining the breaking loads. The experiment result analysis showed that ...

[Date (May 26, 2013)]

Objective
Theory overview
A resonant circuit which is in series consists of a capacitor, a resistor and an indicator connected in a loop. At some frequency the inductive and capacitive reactances magnitudes becomes equal and since they are opposite each other they effectively cancel each other. This makes the circuit to be purely resistive as it only ‘sees’ the resistor. Therefore at the resonance frequency the current becomes maximum. At any lower or higher frequency, the net difference between XC and XL should be summed with the value of the resistor; this produces higher impedance ...

Executive Summary 3

Overview of Current Situation 3
Summary of Needs and Objectives 4
Summary of Recommendations 4
Summary of Expected Outcomes 4
Important Information 5
1.0 Objective 6
2.0 Current Situation 6
2.1 How to get there 7
3.0 Recommendation 1 9
3.1 What is Salary Sacrifice? 9
3.2 Steps 9
3.3 Benefits of the Recommendation 11
3.4 Risk Associated with the Recommendation 13
4.0 Recommendation 2 14
4.1 Steps 15
4.2 Benefits of the Recommendation 15
4.3 Risk Associated with the Recommendation 15
4.4 Alternatives Researched and Why Rejected 16
3.5 Conclusion 17
5.0 Superannuation Withdrawals - Taxation Implications 17
...

Introduction

In the operation of a system, organization or machine, the extent of success lies in its ability to produce the highest possible results within a specified period of time (Boyer & Verman, 2009). This effectiveness focuses on the capacity which is the quality of work done in a defined period of time. This paper explores the differences between peak capacity and effective capacity in relation to production levels. It weighs the various strengths and weaknesses presented by each capacity. A case study of capacity cushions for airlines explores both concepts according to Sasaki (2008). It also expresses how the two ...

Executive Summary

McDonald’s, with its huge customer base and steadily increasing revenue, has proved the excellence of it operations management. Operations management can be defined as a long term strategy that shapes a company’s operations in such a way that it is aligned to organisational goals, market requirements and available resources. The objective of this paper is to delve through the effective operations management strategies of McDonald’s that have significantly contributed to its huge success. It studies the various the components of operations management and how effectively it has been utilised in McDonald’s.
The corporation ...

Organization Background

Today knowledge management is very important for organizations to survive in a dynamic business environment. Knowledge management is considered as one of the important functions which needs plan, organize the activities and motivate and control the human resources to improve the overall productivity of the organization.
GS (Global Software) Ltd. is a New York based software development and consultancy company which provides software solutions to banking and insurance companies all over the United States. It is having one thousand employees working in 12 offices in 4 major cities New Jersey, Washington, Chicago and head office in New York. GS ...

Abstract

Concrete acts as one of the most essential and cost-effective construction material made from a mixture of sand, cement, aggregates, and water. Cement acts as a binder for holding all the components together. Engineers working in the construction site must understand the purpose of the construction because different structures require different concrete strengths. The strength of cement paste used controls the overall strength of concrete that depends on the water-cement ratio. The following experiment was conducted to investigate different mechanical and physical properties of concrete.

Objective: To determine mechanical properties of concrete.

Materials used: Aggregate (coarse and fine), sand, cement, water, compressive machine, cylindrical and rectangular ...

Introduction.

The European emissions trading scheme (EU ETS) was launched in 2005 to curtail adverse climatic changes in the Europe. Today, the EU ETS is the largest emissions trading scheme in the world. Its foundation and motivation was based on the EU climate policy of reducing the greenhouse gas emissions emitted from human activities that pose dangerous and harmful climatic changes to the world. It currently covers 1100 factory plants and other high energy plants in all EU member states. The EU ETS was the first cap-and –trade allowances system for carbon four oxide emissions alongside other greenhouse gases at ...

Analysis of Canadian Housing Investment Opportunities

Analysis of Canadian housing investment opportunities
Executive Summary
The Canadian Housing market has historically offered enough returns with significant volatility over the last two decades. It is the most stable of housing markets around the world and is favored by the changing demographics. From well-regulated financial markets to encouraging immigration policies, Canada’s housing market is poised for surges in demand, given stable supply, and is supported by reliable financial regulation. Investors with a medium to long-term horizons, as well as people simply wish to enjoy Canada’s peaceful lifestyle, would all benefit from the diverse investment choices. We ...

TA: Your TA's name

Partner: Your partner's name
Thevenin and Norton Circuit Theory
Introduction
This experiment is aimed at putting to practice the Thevenin and Norton theories of dc resistor networks. These theories provide for techniques that make circuit analysis easier. In order to achieve this, a network of resistors connected to active sources is reduced to a single resistance which is connected in series with the voltage source. The single resistance is the Thevenin resistance of the network while the voltage source is the Thevenin voltage of the network. Norton’s Theorem also helps us simplify circuit analysis by replacing the network ...

Daikin Asia Servicing Pte Ltd is a service company that deals with the distribution of air- conditioning wares and the related air conditioning accomplices in Asia, Middle East region, Africa region and oceanic region. The company was established in 1966 and is based in Singapore. In addition, the company provides technological information, administrative support services, marketing services and vending support services to their distributors. The company also actively supports their distributors in the area of management by enlightening them on inventory and logistics management. This is done as a way of enhancing performance of their core distributors and also ...

Electric vehicle

  
Abstract
The following paper discusses at length the various kinds of Electric Vehicles (EV) available by giving examples and discussing their specifications in order to make the reader aware of the available electric vehicles in the market. The Greenhouse effect is a major cause of concern and can be controlled by watching ones carbon footprints. Investing in an electric vehicle is its stepping stone. The paper is thus written with the view of providing a comprehensive view in the available short, medium and long range electric vehicles.

The growing percentage of air pollutants let into the air due to ...

Final Exam Geology

Patterns of Surface Ocean Currents

Surface currents are found in the upper four hundred meters of an ocean body and they form major patterns such as eddies, upwelling, and gyres (Garrishon, 2007). Surface currents result from wind energy that is concentrated in both north and south hemispheres forming trade winds which are easterlies and westerlies (Garrishon, 2007). Waves on the sea surface transfer some of the energy from the moving air to the water by friction. Pulling of wind on the surface of ocean causes an accumulation of water with the water ...

Lab Report: Internal Resistance of a Battery

Lab Report: Internal Resistance of a Battery

Abstract

This purpose of this lab is to demonstrate the effect of internal resistance of a household battery on circuits and to measure the power transfer through it. The battery is connected in series with a rheostat that acts as a variable resistor. The value of resistance is varied across the available rheostat range. The voltage at the output is measured across rheostat and its effect on the charge depletion of battery is analyzed. The hypothesis of the experiment is that as the current flowing through the load increases with decrease in resistance, ...

Introduction

Initially there were beliefs that, MMPs are jointly able to degenerate all constituents making up the extracellular matrix (ECM) together with basement membrane that confines their operations to tissue reconstruction as well as the preservation. Nonetheless, the contemporary studies also signify that MMP-1 is responsible for controlling the production or else the activation of the chemokines. At this point, it is critical to understand that MMP-1 is among other MMPs.
Similarly, the knowledge holds it that MMP- 1 cleaves a peptide bond beforehand a residue comprising of a hydrophobic adjacent chain, for instance Met and Leu. The other sideways ...

16.1 Combining Beliefs and Desires under Uncertainty
Our understating of the world is mostly constrained by the lack of enough information and uncertainty of different outcomes. Despite this incompleteness and uncertainty we have to act and make conclusions. Decision theory is concerned with recognizing the qualities, vulnerabilities and different issues important in a given choice, its consistency, and the ensuing ideal choice, in an episodic environment [1]. In an episodic environment, the execution of an agent is subject to various discrete occurrences, with no connection between the executions of an agent in diverse situations. Episodic situations are less complex ...

The main objective of this experiment is to observe “slow” transient voltages in a long time constant RC circuit using a multimeter and to observe “fast” transient voltages in a short time constant RC circuit using an oscilloscope.

Materials and Equipment:

- Variable voltage DC power supply (0-20 volts, 0-1.5 amps)
- Digital multimeter (DMM)
- Decade resistance and capacitance box
- 50 µf, 100 µf capacitors (rated 20v or higher)
- Carbon film resistors: 1MΩ
- Single throw, double pole switch
- Oscilloscope & AC function generator or myDAQ Module, PC with Multisim

THEORY

A capacitor is made up of two conducting plates ...

Group Number:

ABSTRACT
The RLC resonance in a circuit is a circuit in which the arrangements follow or consist of a resistor, inductor and capacitor. This lap report is not a confined order. It can take a different order, i.e. an inductor, a resistor and a capacitor thus LRC. This arrangement can be connected in series or parallel depending on the topic in question. In this circuit, RLC circuit resonance, form a harmonic oscillation for current in seen in the cathode ray tube, oscilloscope. This laboratory work or experiment tries to determine the behavior of an RLC resonance circuit in terms ...

Portfolio Management

Introduction
The objective of this report is to understand the performance of various stocks ranging from different industry over a period of three weeks. The companies selected by us include:
- Apple Inc.
- Ebay Inc.
- Delta Airlines
- Coca-Cola Company
- Bank of America
- Wells Fargo
- Banco Santander
- JP Morgan
- Progressive Corp
- Pepsi
- Mcdonald
- AT&T
The companies were selected as each one represented their industry significantly while the banking stocks were selected primarily because of recent growth in the banking sector amid the economic recovery in the United States. As ...

Dear Client,

This has reference to your revision request. All the questions (except for one) have been answered. I have made the answers obvious and done and added a few words here and there to make the answers more prominent. Everything is marked in the two pages of the ‘copy of the report’ which follows this letter. Please go through the same and tell me if you still think the paper needs revision, after reading it. In case you want a revision, I’ll be happy to do it for you but you have to tell me what needs to be ...

Executive summary:

As a fluid flows through a pipe, there are numerous losses due to the nature and characteristic of the pipe. Such losses can be investigated in the laboratory by setting up an experiment. This report, presents the results and discussion of an experiment set up to investigate fluid flow. The laboratory experiment is designed in order to determine the relationship between the head losses resulting due to friction and the velocity of flow of the water. Secondly, the experiment is aimed at comparing the measured and calculated values of head loss determined using the pipe friction equation. The data ...

Coarse number and lab section

Letter of Transmittal
- Deflection and Loading Tables and Graphs
- Fiber Glass loading and deflection Table and Graphs

Where :

P= load,
L= span length,
b=width,
and d=depth
- Calculation of flexural strain:
εf= 6∆d/L2

Where ∆ represents maximum deflection

- Calculation of modulus of rupture MOR
MOR=Mc/I
Where M = moment at mid-span
C=d/2
I= Moment of inertia
- Calculation of tangential modulus of elasticity
Et=PL3/48I∆

Where

P= load
∆=deflection at centre span
I=moment of inertia
L=span length
- Calculations

Glass fiber parameters

- Modulus of Rupture (MOR)
MOR=Mc/I
I= pr2 =20*1.842 =67.712 lb Inch.2
M= 0.945*20=18.9 lb Inch
MOR=18.9*0.057567.712=0.016lb/Inch2
- Tangential Modulus of elasticity
...

Introduction

The major experiments that are conducted in the determination of enzyme kinetics are those that vary the amount of concentration in order to measure the enzyme velocity . The aim of such experiments is to determine the Km or the amount of the substrate that gives half the enzyme velocity, as well as the Vmax, which is the maximum velocity attained by the enzyme . In addition, the enzyme kinetics may be presented graphically using the Eadie–Hofstee diagram. The diagram made by plotting the rate of reaction as a function of the ratio between rate and concentration of the substrate ...

Group number: 7

Section SLN: 7242S
TA’s name:
Part 3: Wooden block with one weight.
Mass of the wooden block, mb = 0.122 kg
Mass of the heavy weight 1, mw1 = 0.494 kg
=====================================================================

Part 4: Statistical distribution of data.

The attached histogram has been created for the
static / kinetic (select one)frictional force data.
III. Data Analysis.

Part I: Determination of the coefficient of static friction

- Based on the data collected for the wooden block carrying two weights and sliding along the lab table the coefficient of static friction was determined as follows:
(Show equation and sample calculation)
fs = μs N
where fs =Average frictional force = 7.889 N
N = Total normal load = (0.122 + 0.494 + ...

Introduction

In the design of energy efficient house, three key factors need to be considered. First is the materials and construction. The chosen materials should be durable, renewable and have high insulation levels. Second, the resource value unto which the construction is done is important. Finally, putting energy use at the centre of the design process is the key factor that surpasses all other factors.
Having realized that embedded systems in the distribution network could lead to great energy savings, especially in the domestic situations, it is feasible to come up with energy efficient house that can utilize renewable and ...

Abstract

A hybrid car is a car used to drive the drive wheels more than one energy source.
Hybrid car called the vehicle driven by using the hybrid power plant. A distinctive feature of the hybrid power plant is to use two or more sources of energy and their corresponding engines that convert energy into mechanical work. Some sources of information used, the term "hybrid engine", which from a technical point of view is incorrect.
Despite the diversity of sources of energy (thermal energy of gasoline or diesel fuel, electricity, compressed air energy, the energy of the compressed liquefied gas, ...

After my first engagement in yoga, I feel aches in my body joints and some slight headache. My heart was pumping first due to the vigorous exercise though I feel internally refreshed. Yoga not only relaxed my physical muscles but also my psychological well-being. For the first time after a long period, I was able to reflect on myself. I could feel blood move through my veins and even count my heartbeats in a minute. Despite the aching and some few muscle pulls and headache I suffered thereafter, I appreciated the internal relaxation than came with the practice of ...

Cardiff University

Speaker – Ray Davies
HM specialist inspector
Health and Safety is a very important part of any work environment. Many laws and regulations are put forward to maintain proper regulations in a work environment. HSE, the health and safety Executives are a body that help the organizations in following all such regulations put forward by the law for the safety and health of the workers and the working environment. (Krause T R The behaviour-based safety process 1997)
The speech was about the importance of health and safety in normal operations of any work place, and how these can be handled ...

<Student’s name>

Part 1. Solar Panel History

The history of Solar panels takes it beginning from the 7th Century B.C. Now, the energy sector of economy has the greatest impact on our lives. Power supply is the basis of the normal functioning of any production, and, consequently, the entire human civilization. Heat and light homes, work machines and units in production, traffic and rural suffering - all these many faces of Energy. Various technological advances have already become part of life for us, but they are possible only when adequate and affordable energy supply, due to the development of alternative energy sources, ...

A forty-three year old male with cases of irritated eyes and increasingly blurry vision. The man also reports cases of skin irritation which are at certain instances severe and cases of difficulty in breathing.

His skin irritation and difficulty in breathing stared six months ago.at the onset these complications were mild and isolated in their frequency but gradually they are becoming more persistent. Irritation of the eyes started three months ago and his vision started to get blurry a month ago.

Past medical history

Noncontributory.
Family history
His wife, parents, and two sisters are all perfectly healthy. His three daughters are also ...

Alabama Department of Corrections

The Alabama Department of Corrections (ADOC), which is headed by Commissioner Kim T. Thomas, has a total of fifteen major correctional facilities located in the different places within the State. Along with these major facilities, the ADOC also has thirteen Work Centers and Two Private Facilities. ADOC’s mission is to provide programs that will rehabilitate convicted felons in a humane and secure environment with the help of professionals in managing the facilities and they prepare the offender for their social re-entry (state.al.us).
The Department’s correctional programs are usually engage with offenders who able to work, attend programs ...

Executive Summary

The Canadian Housing market has historically offered enough return with significant volatility over the last two decades. It is the most stable of housing markets around the world and is favored by the changing demographics. From well-regulated financial markets to encouraging immigration policies, Canada’s housing market is poised for surges in demand, given stable supply, and is supported by reliable financial regulation. Investors with a medium to long-term horizons, as well as people simply wish to enjoy Canada’s peaceful lifestyle, would all benefit from the diverse investment choices. We suggest starting with investing in residential real estate ...

(QAM) Laboratory Report

For (XXX)

Objective:
Components required:
A carrier source, data source, phase shifter, multiplier, symbol mapping, noise channel, PCB board, phase scope and oscilloscope.
Theory:
There are two types of modulation technique namely analog and digital. QAM is a technique that uses both analog and digital modulation technique. It is the abbreviation used for Quadrature amplitude modulation.
In analog modulation scheme it passes the two message signals by varying the amplitude of the two carrier waves using amplitude modulation method. In the case of digital modulation technique two digital bit streams are transferred in which amplitude shift keying (ASK) ...

Introduction

A dish washer is a mechanical device that is used in the cleaning of eating utensils and dishes. They are mainly found in restaurants and homes. The existence of the dish washing device has become a staple in many homes because, unlike the manual dish cleaning process, dishwashers spray the hot water in the temperature range of 55-75 degrees centigrade on the dishes. This has made dish washing process easier and eliminates the danger of breaking utensils and injury that is associated with mechanical washing.

Design concepts

The best dish washing devices are designed to reduce the probability of inflicting injury ...

Wireless Info Systems

Wi-Fi
Wi-Fi is an acronym for Wireless Fidelity. It is a groundbreaking invention in the field of networking and has been finding increasing uses everyday. Based on IEEE 802.11a/g, current Wi-Fi systems support a maximum data rate of up to 54mbps. There are different features and aspects of this technology, which define it and its applications. Some of the most important and prominent uses of Wi-Fi Technologies are:
Based on Radio Signals: Radio Signals form the basis of operations for the Wi-Fi technology. The data is transmitted through these radio signals from one Wi-Fi enabled device to the other. ...

GPRS (General Packet Radio Service) - an add-on technology, mobile GSM, performs packet data transmission. GPRS allows the user to the cellular network to exchange data with other devices in the GSM network and external networks, including the Internet. GPRS involves charging by volume of data sent / received data, and not on time spent online.
GPRS enables people to enjoy advanced, feature-rich data services, such as e-mail on the move, multimedia messages, social networking and location-based services(GSMA).

Architecture:

GPRS data service built over the existing network GSM. At a structural level, the GPRS system can be divided into ...

Aerobic is a biological terms which means “with air” or “in the presence of air”. When it comes to define Aerobics, we replace the word “air” with “oxygen”. Yes, aerobics or aerobic exercise includes all such steps or activities which involve a systematic inhale and exhale of oxygen, which enhances cardiac strength and also helps in fat loss by adequate metabolism activity. Every such exercise that enhances efficiency of respiratory and circulatory systems is included in aerobics; for example cycling, swimming, dancing, jogging, brisk walking etc. As these exercises involve stretching and strengthening too, these enhances the flexibility of ...

Abstract

Amylase from Bacillus Subtilis and Aspergillus oryzae were studied as representative candidates for bacterial and fungal enzymes, respectively. The activities of these two enzymes were studies comparatively over a period of 10 minutes and at temperatures of 0, 40, 60 and 95°C. The experiment was conducted to find the most effective temperatures for bacterial amylase and fungal amylase to catalyze starch hydrolysis. The data suggest that fungal enzyme was relatively more active, particularly in the first 6 minutes, than the bacterial counterpart at 0°C.
On the other hand, the fungal enzyme activity deteriorated more rapidly than that ...

for Argentina and Hungary
Olomoze’s products would be aggregated in the group or category where tea milk and bubble tea are also classified. From the industry or macroeconomic perspective, while they may be differentiated, these products are considered as alternatives or substitutes to each other . Instead of using dairy or ice cream industry data (which comprise a bigger industry), Taiwan’s aggregated demand for tea milk and similar products are used for demand estimation.
Taiwan’s consumption of or demand for these products is estimated at about 1.5 billion cups a year. Each cup is about 8 ounces, ...

Introduction

In the contemporary world, the medical field and the business world are the most recognized in all careers fields. Many factors affect career choices and identifying these factors gives tutors, parents, and the overall industry an idea where the students place more emphasis and trust in the career selection process. People or student seeking a firm foundation in their life has an option either to select a career in the medical field or a career in the entrepreneur field. The purpose of this paper is to compare the career choices both in the medical field and in the business ...

Marketing concepts are approaches that are used by companies to market their products, satisfy consumer expectations and increase profits. Consumer expectations and preferences are the biggest influences of the choice of a marketing concept. In the process of satisfying customer needs, the company achieves its objective of making profits or increasing its market share. There are many concepts of marketing such as market segmentation, product cycle and customer satisfaction. These concepts are used in various industries because of their flexibility and effectiveness. Market segmentation aims at dividing the market into groups that have homogeneous needs. Product cycle model is ...

Introduction

Inventories are the raw materials which the company has stored for use in production. Inventory management refers to the policies and inventory models that the company uses to conduct its operations. There are different kinds of inventory management models which are dependent on the nature and types of inventory that the company holds.

There are certain factors that have to be considered when considering the optimum inventory model. There is the ordering cost which is the price the company pays to the supplier for placing an order. It is assumed that the ordering cost has a variable and a ...